Enterasys Matrix 7GR4202-30 Installationsanleitung PDF herunterladen (Seite 20)

Document Conventions

xviii About This Guide

DOCUMENT CONVENTIONS

This guide uses the following conventions:

NOTE: Calls the reader’s attention to any item of information that may be of special

importance.

TIP: Conveys helpful hints concerning procedures or actions.

CAUTION: Contains information essential to avoid damage to the equipment.

ELECTRICAL HAZARD: Warns against an action that could result in personal injury or

death due to an electrical hazard.

WARNING: Warns against an action that could result in personal injury or death.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 91 92

Matrix E1 Series 1
(1H582-25 and 1H582-51) 1
Installation Guide 1
FCC NOTICE 4
INDUSTRY CANADA NOTICE 4
VCCI NOTICE 4
CLASS A ITE NOTICE 4
SAFETY COMPLIANCE 5
SAFETY INFORMATION 6
CLASS 1 LASER TRANSCEIVERS 6
ENTERASYS NETWORKS, INC 7
PROGRAM LICENSE AGREEMENT 7
DECLARATION OF CONFORMITY 10
Contents 11
TROUBLESHOOTING 12
SPECIFICATIONS 12
GBIC SPECIFICATIONS 13
About This Guide 17
STRUCTURE OF THIS GUIDE 18
HOW TO USE THIS GUIDE 19
RELATED DOCUMENTS 19
DOCUMENT CONVENTIONS 20
Introduction 21
1H582-51 22
1H582-25 22
1.2 CONNECTIVITY 23
1G-2GBIC 24
1.3 STANDARDS COMPATIBILITY 25
1.4 GETTING HELP 25
Network Requirements 27
2.2 10BASE-T NETWORK 28
2.3 100BASE-TX NETWORK 28
2.4 100BASE-FX NETWORK 28
2.5 1000BASE NETWORK 28
Hardware Installation 29
3.2 UNPACKING THE DEVICE 30
3.3 INSTALLING OPTIONS 31
1H582-51 shown 33
Coverplate 33
Coverplate Captive Screws (2) 33
Front Panel 33
1G154-09 34
3.5 INSTALLING OPTIONAL GBICs 35
3.5.1 Side Clip GBICs 36
3.5.2 Locking Bar GBICs 38
Preparation 39
Installation 39
Installing Optional GBICs 40
3-12 Hardware Installation 40
Removing the Mini-GBIC 43
3.7 INSTALLING THE DEVICE 44
3.7.1 Rackmount Installation 44
3.7.1.2 Installation 45
➁ in the rackmount kit 46
➁ (user supplied) 47
3.7.4 Connecting Power 48
3.8 CONNECTING TO THE NETWORK 49
3.8.1 Connecting UTP Cables 49
Connecting to the Network 50
3-22 Hardware Installation 50
Hardware Installation 3-23 51
Multimode Fiber Optic Cables 54
➀, key side down ➁, into the 55
• Transmit (TX) 56
• Receive (RX) 56
Hardware Installation 3-29 57
3.9.1 What Is Needed 58
Hardware Installation 3-31 59
Parameter Setting 59
3-32 Hardware Installation 60
3.9.4 Connecting to a Modem 61
DB9 Connector (Female) 62
Completing the Installation 63
Hardware Installation 3-35 63
RJ45 DB25 63
“Getting Help” in Chapter 1 64
Troubleshooting 65
4.1 USING LANVIEW 66
Using LANVIEW 67
Troubleshooting 4-3 67
Table 4-1 LANVIEW LEDs 67
4.2 TROUBLESHOOTING CHECKLIST 68
Troubleshooting Checklist 69
Troubleshooting 4-5 69
4-6 Troubleshooting 70
4.3 USING THE RESET BUTTON 71
Specifications 73
(Section A.1) 73
A-2 Specifications 74
Item Specification 74
SC fiber optic connection 76
A.5 REGULATORY COMPLIANCE 77
Optional Installations and 79
Mode Switch Bank Settings 79
ÑOS, AL IGUAL QUE AL APARATO 80
12 Cover Screws 81
1H582-51 Device (shown) 81
B.3 SETTING THE MODE SWITCHES 82
Setting the Mode Switches 83
B.4.1 Locating SIMMs 84
B.4.2 Removing the DRAM SIMM 84
Release Tabs 85
DRAM SIMM 85
Connector 85
SIMM Alignment Notch 86
Connector Fingers 86
SIMM Alignment Notches (2) 86
Connector Clips 86
GBIC Specifications 87
C.3 REGULATORY COMPLIANCE 90

Kommentare zu diesen Handbüchern

Keine Kommentare

Enterasys Matrix 7GR4202-30 Installationsanleitung Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Netzwerk-Switches Enterasys Matrix 7GR4202-30