7.5x9-inch cover with bleed on 4 sidesEnterasys Matrix® N77C107 ChassisHardware Installation GuideP/N 9033851-06
viii 4. EXPORTRESTRICTIONS. YouunderstandthatEnterasysanditsAffiliatesaresubjecttoregulationbyagenciesoftheU.S.Government,including
ix8. AUDITRIGHTS. YouherebyacknowledgethattheintellectualpropertyrightsassociatedwiththeProgramareofcriticalvaluetoEnterasys,and,a
x
xiContentsABOUT THIS GUIDEUsing This Guide...
xiiASPECIFICATIONS AND REGULATORY COMPLIANCEA.1 Physical Specifications...
xiiiAbout This GuideWelcome to the Enterasys Matrix® N7 7C107 Chassis Hardware Installation Guide. This guide lists the features and options of theN7
xivUSING THE ENTERASYS MATRIX N7 7C107 CHASSIS SERIES MANUAL SETSeparate manuals have been developed for the 7xxxxx series DFE modules that can be ins
xvElectrical Hazard: Warns against an action that could result in personal injury or death due to an electrical hazard.Riesgo Electrico: Advierte cont
xvi
Introduction 1-11IntroductionThis chapter provides an overview of the Enterasys Matrix N7 chassis and its features. Also covered in this chapter are t
Overview1-2 IntroductionFigure 1-1 The N7 7C107 Chassis with Redundant Power Supplies1 Chassis (7C107) 3 Fan tray (6C407)2 Module slots (7 total) 4 Re
FeaturesIntroduction 1-31.2 FEATURESThe following provides an overview of the chassis features.N7 7C107 Chassis ModulesThe N7 chassis has seven slots
Features1-4 IntroductionPower Supply Status Using ManagementThe N7 chassis power supplies report information to the DFE modules installed in the chass
Getting HelpIntroduction 1-5Standalone or Rack Mountable ChassisThe N7 chassis can be installed as a freestanding unit on a shelf or table. The N7 cha
Getting Help1-6 Introduction
Installation Requirements and Guidelines 2-12Installation Requirements and GuidelinesThis chapter describes the following:• Site guidelines that must
Configuration Guidelines2-2 Installation Requirements and Guidelines• Ambient temperature at the installation site must be maintained between 5° and 4
LANVIEW LEDsInstallation Requirements and Guidelines 2-3Figure 2-1 6C207-3 Power Supply LEDs 1 POWER LED 2 FAN LEDTable 2-1 Power Supply (PS) LED Stat
LANVIEW LEDs2-4 Installation Requirements and Guidelines2.3.2 Fan Tray LEDRefer to Figure 2-2 for the location of the fan tray LED. Table 2-2 describe
Enterasys Matrix N7 Chassis Setup 3-13Enterasys Matrix N7 Chassis SetupThis chapter contains instructions on setting up the Enterasys Matrix N7 chassi
iNoticeEnterasys Networksreservestherighttomakechangesinspecificationsandotherinformationcontainedinthisdocumentanditswebsitewitho
Unpacking the Enterasys Matrix N7 Chassis3-2 Enterasys Matrix N7 Chassis Setup4. Remove and save the four screws fastening the rear shipping bracket/s
Unpacking the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-3Figure 3-1 Unpacking the Matrix N7 ChassisÂÃÃÀÁÄÅÆÇÈÉÅÅÇÇÇ
Setting Up the Enterasys Matrix N7 Chassis3-4 Enterasys Matrix N7 Chassis Setup3.2 SETTING UP THE ENTERASYS MATRIX N7 CHASSISThe following sections de
Setting Up the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-53.2.2.1 Installing the Rubber FeetTo install the rubber feet, see Figur
Setting Up the Enterasys Matrix N7 Chassis3-6 Enterasys Matrix N7 Chassis Setup3.2.2.2 Installing the Cable Management BarCables can be attached along
Setting Up the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-73.2.3 Rack Mounting the Enterasys Matrix N7 ChassisThe N7 chassis can b
Setting Up the Enterasys Matrix N7 Chassis3-8 Enterasys Matrix N7 Chassis Setup3.2.3.1 Installing the ShelfTo install the shelf, proceed as follows:1.
Setting Up the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-93.2.3.2 Installing the Enterasys Matrix N7 ChassisTo install the N7 cha
Setting Up the Enterasys Matrix N7 Chassis3-10 Enterasys Matrix N7 Chassis SetupFigure 3-5 Rack Mounting the Enterasys Matrix N7 Chassis1 Rack mountin
Setting Up the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-113.2.3.3 Attaching the Electrostatic Discharge Wrist StrapThe Electrost
ii Regulatory Compliance InformationFederal Communications Commission (FCC) NoticeThisdevicecomplieswithPart15oftheFCCrules.Operationissub
Setting Up the Enterasys Matrix N7 Chassis3-12 Enterasys Matrix N7 Chassis Setup1. Unpack the power supply by removing it from the shipping box and sl
Setting Up the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-13Figure 3-7 Installing the Power Supply Module(s)After completing the p
Setting Up the Enterasys Matrix N7 Chassis3-14 Enterasys Matrix N7 Chassis Setup3.2.5 Removing a Power SupplyTo remove a 7C203-1 power supply, refer t
Setting Up the Enterasys Matrix N7 ChassisEnterasys Matrix N7 Chassis Setup 3-15Figure 3-8 Removing a Power Supply from a Powered-Up Chassis1 Power sw
Powering Up THE N7 Chassis with Power Supplies3-16 Enterasys Matrix N7 Chassis Setup3.3 POWERING UP THE N7 CHASSIS WITH POWER SUPPLIESTo power up the
Removing and Reinstalling the Fan TrayEnterasys Matrix N7 Chassis Setup 3-173. Ensure that the Power LED on each power supply is green.4. Ensure that
Removing and Reinstalling the Fan Tray3-18 Enterasys Matrix N7 Chassis SetupFigure 3-10 Removing the Fan Tray3.4.2 Reinstalling the Fan TrayTo reinsta
Removing and Reinstalling the Fan TrayEnterasys Matrix N7 Chassis Setup 3-194. Slide the fan tray into the chassis until the faceplate of the tray is
Removing and Reinstalling the Fan Tray3-20 Enterasys Matrix N7 Chassis Setup
Specifications and Regulatory Compliance A-1ASpecifications and Regulatory ComplianceThis appendix provides operating specifications for the Enterasys
iiiElectromagnetic Compatibility (EMC)Thisproductcomplieswiththefollowing:47CFRParts2and15,CSAC108.8,2004/108/EC,EN55022,EN61000‐3‐2
Power Supply RequirementsA-2 Specifications and Regulatory ComplianceA.1.1 Torque ValuesThefollowingtabledescribestherecommendedtorquevaluesto
Regulatory ComplianceSpecifications and Regulatory Compliance A-3A.4 REGULATORY COMPLIANCEThis equipment meets the following safety and electromagneti
Regulatory ComplianceA-4 Specifications and Regulatory Compliance
iv ѻѻક䇈ᯢк䰘ӊSupplement to Product Instructions ᳝↦᳝ᆇ⠽䋼ܗ㋴(Hazardous Substance) 䚼ӊৡ⿄(Parts) 䪙3E∲+J䬝&G݁Ӌ䫀&U⒈㘨㣃3%%⒈Ѡ㣃䝮3%&apo
vVCCI NoticeThisisaclassAproductbasedonthestandardoftheVoluntaryControlCouncilforInterferencebyInformationTechnologyEquipment(VCC
vi Declaration of ConformityApplicationofCouncilDirective(s): 2004/108/EC2006/95/ECManufacturer’sName: Enterasys Networks, Inc.Manufacturer’sAddr
viiENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,CAREFULLY READ THIS LICENSE AGREEMENT.Thisdocu
Kommentare zu diesen Handbüchern